Products

Home
Products
Standard Cylinder CA2 series(Φ40~Φ100)

Standard Cylinder CA2 series(Φ40~Φ100)

● 5~15% less mass than CA1 series.
● Improved cushioning capacity, no rapid extension of the piston rod.
● The cushion valve is easier to adjust and the cushion valve is not exposed to the cylinder head surface.
● The kinetic energy that can be absorbed can be increased by up to 30% compared with CA1 series.Seal life can be extended about 5 times.
● The downward bending of the piston rod is reduced by 5~10% compared with CA1 series.
● Installation dimensions are the same as those of CA1 series.
● In addition to Rc, there are NPT thread and G thread

Share to:

Model Number Indication

Standard Specifications

Bore (mm)	40	50		63	80		100
Operating Pressure Range	0.05~1.0MPa
Ambient and fluid temperature	Non-magnetic switch: -10℃~+70℃, with magnetic switch: -10℃~+60℃.
Used piston speed	50~500mm/s
Cushioning	Air lock
Stroke length tolerance (mm)	~250:+1.0 0		251~1000:+1.4 0			1001~1500:+1.8 0
Oil feed	Unnecessary
Tube caliber (Rc)	1/4	3/8			1/2

Stroke/Magnetic switch options

Bore (mm)	*Standard itinerary (mm)	**Magnetic switch model		Magnetic Switch Mounts
		Tie Rod Installation		M9	A54 only
40	25,50,75,100,125,150,175,200, 250,300,350,400,450,500	M9N M9P M9B	A54	BA7-040	BT-04
50	25,50,75,100,125,150,175, 200,250,300,350,400,500,600			BA7-063	BT-06
63
80	25,50,75,100,125,150,175, 200,250,300,350,400,450, 500,600,700			BA7-080	BT-08
100

*With non-standard stroke
**Wire length notation: no notation -0.5m, L-3m, Z-5m.

External Dimension Drawing (mm)

● Basic type (With a protective cover)

Bore (mm)	Stroke range (mm)			A	AL	□B	B1	□C	D	E	F	G	H1	J	K	KA	M	MM	N	P	S	Unprotected sleeve				Protective sleeve
Bore (mm)	Unprotected sleeve		Protective sleeve	A	AL	□B	B1	□C	D	E	F	G	H1	J	K	KA	M	MM	N	P	S	H	ZZ	e	f	h	l		ZZ
40	~500	20~500		30	27	60	22	44	16	32	10	15	8	M8×1.25	6	14	11	M14×1.5	27	1/4	84	51	146	43	11.2	59	1/4 stroke	154
50	~600	20~600		35	32	70	27	52	20	40	10	17	11	M8×1.25	7	18	11	M18×1.5	30	3/8	90	58	159	52	11.2	66	1/4 stroke	167
63	~600	20~600		35	32	85	27	64	20	40	10	17	11	M10×1.5	7	18	14	M18×1.5	31	3/8	98	58	170	52	11.2	66	1/4stroke	178
80	~750	20~750		40	37	102	32	78	25	52	14	21	13	M12×1.75	10	22	17	M22×1.5	37	1/2	116	71	204	65	12.5	80	1/4 stroke	213
100	~750	20~750		40	\|37	116	41	92	30	52	14	21	16	M12×1.75	10	26	17	M26×1.5	40	1/2	126	72	215	65	14	81	1/4 stroke	224

● Basic type，Flange type，Single earring type

Bore (mm)	Leg seat								Pedestal								Single earrings
Bore (mm)	Part NO.	LH	LX	LY	X	Y	LT	LD	Part NO.	FT	FD	B	FV	FX	FY	FZ	Part NO.		CD	U	L	RR	CX
40	CA2-L04	40	42	70	27	13	3.2	9	CA2-F04	12	9	71	60	80	42	100	CA2-C04	10		16	30	10	15
50	CA2-L05	45	50	80	27	13	3.2	9	CA2-F05	12	9	81	70	90	50	110	CA2-C05	12		19	35	12	18
63	CA2-L06	50	59	93	34	16	3.2	11.5	CA2-F06	15	11.5	101	86	105	59	130	CA2-C06	16		23	40	16	25
80	CA2-L08	65	76	116	44	16	4.5	13.5	CA2-F08	18	13.5	119	102	130	76	160	CA2-C08	20		28	48	20	31.5
100	CA2-L10	75	92	133	43	17	6.0	13.5	CA2-F10	18	13.5	133	116	150	92	180	CA2-C10	25		36	58	25	35.5

● Double earring type，Intermediate trunnion type

Bore (mm)	Double Earrings							Intermediate trunnion
Bore (mm)	Part No.	CD	U	L	RR	CX	CZ	TY	TD	TX	TZ	TT	Part No.
40	CA2-D04	10*0.058	16	30	10	158:3	29.5	62	15-8.832	85	117	22	CA2-S04
50	CA2-D05	12+8.07	19	35	12	18+8:3	38	74	15:21:52	95	127	22	CA2-S05
63	CA2-D06	16*8.07	23	40	16	25+8:3	49	90	28-8:832	110	148	28	CA2-S06
80	CA2-D08	20+0.084	28	48	20	31.5+8:3	61	110	25=8.843	140	192	34	CA2-S08
100	CA2-D10	25+8.084	36	58	25	35.5+8:3	64	130	25:8:899	162	214	40	CA2-S10

● Trunnion Foot

Material：Cast Iron

Model	Bore (mm)	TA	TL	TU	TC	TX	TE	TO	TR	TT	TS	TH	TF	TY	Z	TD-H10 (hole)
CA2-S04	40	80	60	10	102	85	119	17	9	17	12	45	60	62	93	15
CA2-S04	50	80	60	10	112	95	129	17	9	17	12	45	60	74	103	15
CA2-S06	63	100	70	15	130	110	150	20	11	22	14	55	73	90	107	28
CA2-S10	80	120	90	15	166	140	192	26	13.5	24	17	75	100	110	129	25
CA2-S10	100	120	90	15	188	162	214	26	13.5	24	17	75	100	130	135	25-

● Double earring feet

Material：Cast Iron

Swing angle

Bore (mm)	A°	B°	A°+B°+90°
40~100	12°	60°	162°

Model	Bore (mm)	DA	DL	DU	DC	DX	DE	DO	DR	DT	DS	DH	DF	B	Z	TD-H10 (hole)
CA2-B04	40	57	35	11	65	15	85	10	9	17	8	40	52	60	165	10
CA2-B05	50	57	35	11	65	18	85	10	9	17	8	40	52	70	183	12
CA2-B06	63	67	40	13.5	80	25	105	12.5	11	22	10	50	66	85	196	16
CA2-B08	80	93	60	16.5	100	31.5	130	15	13.5	24	12	65	90	102	235	20
CA2-B10	100	93	60	16.5	100	35.5	130	15	13.5	24	12	65	90	116	256	25

● Y – shaped double – elbow joint

Material: cast iron

Model	Bore (mm)	A1	E1	L1	MM	RR1	U1	ND	NX	NZ	L	Cotter pin size	Flat Washer Size
Y-04D	40	22	24	55	M14×1.5	13	25	12	16	38	55.5	φ3×184	Grinding hole 12
Y-05D	50 ·63	27	28	60	M18×1.5	15	27	12	16	38	55.5	φ3×186	Grinding hole12

● Pin for Eye – Loop/Pin for Elbow – Joint

Model	Bore		Dd9	L	￡	m	dthrough-hole	Cotter pins used	Flat washers used
Model	Earrings	Toggle	Dd9	L	￡	m	dthrough-hole	Cotter pins used	Flat washers used
CDP-2A	40	一	10	46	38	4	3	φ3×18￡	Grinding hole10
CDP-3A	50	40 ·50 ·63	12	55.5	47.5	4	3	φ3×18￡	Grinding hole12
CDP-4A	63	一	16	71	61	5	4	φ4×25￡	Grinding hole16
CDP-5A	一	80	18	76.5	66.5	5	4	φ4×25￡	Grinding hole18
CDP-6A	80	100	20	83	73	5	4	φ4×30￡	Grinding hole20
CDP-7A	100	一	25	88	78	5	4	φ4×36￡	Grinding hole24

● I-Shape Single Elbow Fitting

Material: Free-cutting steel

Model	Bore (mm)	A	A	E₁	L1	MM	R1	U1	NDH10	NX
I-04A	40	69	22	24	55	M14×1.5	15.5	20	12	16
I-05A	50 ·63	74	27	28	60	M18×1.5	15.5	20	12	16
I-08A	80	91	37	36	71	M22×1.5	22.5	26	18	28
I-10A	100	105	37	40	83	M26×1.5	24.5	28	20	30

● Rod end nuts (standard equipment)

● Material: Free-cutting steel

Model	Bore (mm)	A	A	E₁	L1	MM	R1	U1	NDH10	NX
I-04A	40	69	22	24	55	M14×1.5	15.5	20	12	16
I-05A	50 ·63	74	27	28	60	M18×1.5	15.5	20	12	16
I-08A	80	91	37	36	71	M22×1.5	22.5	26	18	28
I-10A	100	105	37	40	83	M26×1.5	24.5	28	20	30